Wolf Control4 Integration

Topics:

Use Wolf products with Control4 smart home system?
Control 4 or Control4 connected appliance or smart home information
Smart home appliance upgrade
Home automation

Answer:

The Control4 driver can integrate with Wolf appliances through the Sub-Zero Group Owner's App. This driver enables the Control4 system to read the status of, make changes to, and receive events from the Wolf appliance.

Properties

Device Properties are used to show appliance information.
Note that all properties except for Sabbath Mode and Kitchen Timer are available in Primary and Secondary variations.
The properties shown in the first table below are available for Wolf appliances. Note that not all models support all of these features. Refer to the product Use and Care Guide for further information.

Conditionals

The driver supports Conditionals in the Programming Actions pane. These allow custom programming scripts to make decisions based on any of the properties described below.

Commands

The driver supports Commands in the Programming Actions pane. These allow custom programming scripts to change selected properties.

Variables

The driver provides the following variables. Although it is possible to write to any of these, writes will be ignored unless otherwise indicated. The variables have the same meaning as defined in the Properties section below.
- Primary Set Point
- Primary Temperature
- Primary Probe Temp
- Primary Probe Set Point
- Secondary Set Point
- Secondary Temperature
- Secondary Probe Temp
- Secondary Probe Set Point

Events

The driver supports Device Events. Events can be used to implement automation sequences triggered by activity in the appliance.
Note that Primary and Secondary variations are available for all events except for Set Point Changed, Temperature Changed, or any Timer events.
Custom programming scripts may be written for any of these events.
Supported events are listed in the second table below.

Properties	Description
Cook Mode	Indicates the selected mode of the oven cavity: Off, Bake, Roast, Broil, Bake Stone, Convection Bake, Convection Roast, Convection Broil, Convection, Proof, Dehydrate, Self-Clean, Warm, Eco, Unknown. The mode only active if Cavity is on. The available modes vary depending on oven model and cavity.
Set Point	Indicates the cook temperature when a cook mode is active.
Temperature	Shows the most recently reported temperature. This property may not be reported in real time.
Preheated	True for the remainder of a cook cycle after Temperature property reaches setpoint.
Probe in Use	Indicates that the temperature probe is in use. Not all oven models support probe features.
Probe Temp	Shows the most recently reported probe temperature. This property may not be reported in real time. Not all oven models support probe features.
Probe Set Point	Indicates the probe target temperature when probe is in use. Not all oven cavities support probe features.
Probe LT 10 Degrees	Indicates that the probe temperature is within 10 degrees of the setpoint when probe is in use. Not all oven cavities support probe features.
Probe at Temp	Indicates the probe has reached the target temperature when probe is in use. Not all oven cavities support probe features.
Door Ajar	Indicates whether the cavity door is open or closed.
Light	Indicates whether the cavity light is on or off.
Cavity	Indicates whether the Cook Mode is active.
Cook Timer	Indicates the status of the cook timer: Off, Running, Last Minute, or Ended.
Sabbath Mode	The oven operates in compliance with Star-K sabbath guidelines when Sabbath mode is enabled.
Kitchen Timer	Indicates the status of the kitchen timer: Off, Running, Last Minute, or Ended. Available as Timer 1 and Timer 2 Not all oven models support Timer 2.

Events	Description
Cook Timer Started	A cook timer has been started.
Cook Timer One Minute Remaining	A Timed Cook has one minute remaining.
Cook Timer Complete	A Timed Cook has run to completion. This event does not occur when a Timed Cook is canceled.
Cook Mode Changed	The cook mode has been changed.
Set Point Changed	The cook temperature (setpoint) has been changed.
Temperature Changed	The actual temperature in the oven has changed. This event occurs repeatedly while "Preheat Temperature Reached" stays false.
Preheat Temperature Reached	The oven cavity has reached the set temperature.
Kitchen Timer Started (1 or 2)	The kitchen timer has been set. Some models support only one kitchen timer and do not show the number 1 or 2.
Kitchen Timer One Minute Remaining (1 or 2)	The kitchen timer 1 has one minute remaining. Some models support only one kitchen timer and do not show the number 1 or 2.
Kitchen Timer Ended (1 or 2)	The kitchen timer 1 has ended. Some models support only one kitchen timer and do not show the number 1 or 2.
Meat Probe in Use	The meat probe function has been enabled. Supporting cavities only
Meat Probe within 10 Degrees	The meat probe is within 10 degrees of its set temperature. Supporting cavities only
Meat Probe Temperature Reached	The meat probe has reached its set temperature. Supporting cavities only
Door Ajar	The oven door has been left open for an extended period of time.
Door State Changed	The oven door has been opened or closed.
Self-Clean Complete	A self-clean operation has completed. This event does not occur when a self-clean operation is canceled.

We're standing by with answers

Whether you're shopping for appliances or have questions about those you already own, we've got the resources you need. Talk directly to a customer care expert at the Sub-Zero, Wolf, and Cove service center, or connect with an appliance consultant at an official showroom near you. Get quick answers online, or reach a certified service provider or installer. And much more.

Call us at (800) 222-7820

Customer Care and Support